Body, Door, Engine and Under Hood Labels |
Updated: November 3, 2024 CONTACT |
|
||||
CHASSIS LABELS,
UNDERHOOD STICKERS and BODY LABELS Volvo has stopped making almost all under-hood stickers, body equipment labels or warning labels for older cars. LABELS IN THESE PAGES ARE NOT ORIGINAL FACTORY VOLVO LABELS. They are all custom made based on customer submitted requests. |
Recommended
Directions for Applying Vinyl Stickers and
Labels DRY APPLICATION CLEAN SURFACE: The surface should be clean of dust, grit or oils. Glass should be free of chemicals like Rain-X. Alcohol or a solvent cleaner may be used on non-painted surfaces, but should be tested in an out of sight area first. Oils from your hands can contaminate the surface and degrade the sticker adhesive. FIRM PRESSURE: The adhesive is activated with pressure. Applying the label from one side to the other will help prevent air from being trapped under it. WARM TEMPERATURES: Adhesive sticks better and cures better in warm temperatures. Very cold temperatures will cause the adhesive to have less tack and it may begin to lift. The ideal label and surface temperature is between 70-90°F (21-32°C). When storing labels, keeping them between 60-90°F (15-32°C) is recommended. GIVE THEM TIME: The pressure of applying a label begins the curing process. The adhesive will slowly become stronger over time and will usually be fully cured in about 1-2 weeks. Note about putting labels on plastic surfaces: These stickers sometimes go on plastic surfaces. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment for stubborn surfaces is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item below. |
WET
APPLICATION
This
is
an optional method that works very well, but it has a
slightly steeper learning curve. It is the only
method used by professionals. CLEAN SURFACE: The surface should be clean of dust, grit or oils. Glass should be free of chemicals like Rain-X. Alcohol or a solvent cleaner may be used on non-painted surfaces, but should be tested in an out of sight area first. Oils from your hands can contaminate the surface and degrade the sticker adhesive. PREPARING THE APPLICATION FLUID: If you're tempted to grab some window cleaner, I would not unless maybe it's ammonia and alcohol free. Applying vinyl on a wet surface using proper fluid will allow you to reposition or slide the decal to the correct position. So the fluid needs to be slick. This also allows for better results by reducing air bubbles behind the vinyl. You should use clean water with a small amount of dishwashing liquid soap. The amount of soap should be a few drops in a pint of water (16 ounces). Dishwashing liquid is best, since it's there to break the surface tension of the water, which you can't count on some other soaps to do. Put this liquid in a spray bottle. APPLYING THE VINYL: Remove the decal backing and generously spray the back of the decal (adhesive side). Now generously spray the surface (glass, paint, etc.). Place the decal on the wet surface and spray a little fluid on the front of the decal so the squeegee slides easily. This helps the squeegee works and reduces the chance of scratching the decal surface. Slid the decal it into position. SQUEEGEE TIME: You may use a credit card or a stiff rubber squeegee. If you think there is a chance your tool will scratch the decal, you may wrap a piece of soft, thin cloth over the edge. Something like this tool is perfect: https://www.amazon.com/ABN-High-Quality-Decal-Squeegee. The squeegee will be used for scraping, or "squeegeeing" the fluid out from under the decal. Then let it sit and dry on it's own (in the sun will speed this up). It could take a day or so for things to dry out completely. Here is a good YouTube video for those of you who want to see this method in action: https://www.youtube.com/watch?v=ViAKd-YSQiU For Die
Cut Vinyl Graphics, more here:
https://www.prancingmoose.com/VolvoPrancingMoose.html#diecutinstructions
|
Store in a cool,
dry place, out of direct sunlight until ready to apply. Application is best when temperature is between 50 and 80 degrees Fahrenheit. If applied on glass, clean surface thoroughly, especially if there was ever any Rain-X or other chemicals on it. If applied on a painted surface, keep in mind the adhesive is pretty strong and may need some heat (such as a hair dryer) to remove later. This decal consists of 3 layers: 1. The clear bottom liner (bottom layer) 2. The vinyl decal (middle layer) 3. The clear top mask (top layer) Preparing for Application (Dry Application Method): If applying this to a car, it's best it the car is in a cool area away from direct sun. Before starting the application process, place decal face-up on hard, flat surface. Pressing firmly, rub the top mask back and forth over the vinyl decal. This is to make sure the decal sticks to the top mask when the bottom liner is removed. |
<<< Lifting the Decal
from the
Bottom Liner: Starting at one corner, slowly peel the top mask from the bottom liner. The decal should lift from the bottom liner as you pull and remain attached to the top mask. The sticky side of the vinyl will be exposed, so do not touch it. If any part of the decal is stubborn and not lifting off the bottom liner, then lay the top mask back down, firmly rub the area, and try again. If the decal becomes stubborn and won't lift, you can use a small sharp pick or tool to gently lift the edge up to get it started. Applying the Decal to Surface: Holding the sides of the top mask, lay the image down onto the surface in the desired position. Take your time in positioning, because once it sticks, it stays! Using your fingers or better yet, a credit card, rub across the top mask from the center of the decal outward to push out any trapped air. Then, starting at one corner, slowly peel the top mask off, leaving only the decal. As you peel the mask off, if any part of the decal begins to lift, push the mask back down and rub some more so it stays. |
To see this method in action, you may
view the following YouTube video: https://www.youtube.com/watch?time_continue=6&v=6ZvahnkLJOM |
There is also an alternate WET APPLICATION METHOD for
die
cut graphics in case you find you like that better: https://www.youtube.com/watch?v=KkOMwbf9LQU |
BRAKE CALIPERS If applying to BRAKE CALIPERS, it is recommended they be painted and smooth. Vinyl likes to have a smooth surface to stick to. And the surface needs to be CLEAN. It is optional (some people highly recommend) to spray some high-temp clear sealer over the decal after (ordinary DupliColor aerosol is usually good enough) to help keep the vinyl from lifting later as it can happen. |
Here's a simple video that helps
explain: https://www.youtube.com/watch?v=ijxTWUICiTQ |
And
here's one that's a bit more detailed: https://www.youtube.com/watch?v=dDk_fJTGbbU |
BRAKE CALIPER DECALS |
Custom Arc Die
Cut Decal for Brake Calipers. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White, Red. Size Small: 3 x 0.5 inches (75 x 13 mm): $3.00 ea. Size Medium: 4 x 0.67 inches (102 x 17 mm): $4.00 ea. Size Large: 5 x 0.87 inches (126 x 22 mm): $5.00 ea.
Installation instructions
for die cut decals:
https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions |
|||||
Custom Prancing Moose Die Cut Decal for Brake
Calipers. Extremely high quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White Size: 1 inch tall x 0.6 inches (25 x 15 mm): $2.00 ea. Size: 1.5 inches tall x 0.8 inches (38 x 20 mm): $2.00 ea. Size: 2 inches tall x 1.2 inches (51 x 31 mm): $3.00 ea. Available facing to the LEFT (normal) or to the RIGHT. When done shopping, please proceed to SHIPPING:
Installation instructions for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions |
|||||
Custom
R
Die Cut Decal for Brake Calipers. Extremely high quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. Original logo color was SILVER. Size: 21 mm tall, same size for front and rear caliper. COLOR: Silver (or other?) Set of 4: $5.00 Installation instructions
for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions
|
|||||
Custom
Arc
Die Cut Decal for Brake Calipers. Extremely high quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White, Red. Size Small: 2.7 x 0.47 inches (69 x 12 mm): $3.00 ea. Size Large: 3.3 x 0.6 inches (84 x 15 mm): $4.00 ea. Installation instructions
for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions
|
|||||
|
|||||
STRAIGHT
Logo Die Cut Decal for Brake Calipers. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. Photo LEFT: 100 mm logo on front caliper, 2016 V60 Polestar
Installation instructions
for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions
|
|||||
STRAIGHT "More Squat"
Logo Die Cut Decal for Brake Calipers. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White, Red. Size Small: 2.5 x 0.5 inches (63 x 12 mm): $3.00 ea. Size Large: 4.25 x 0.75 inches (108 x 19 mm): $4.00 ea. |
|||||
Custom Die Cut
Decal for Brake Calipers. Extremely high quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White, Red. Size: Small: 14 mm tall x 47 mm wide (0.55 x 1.8 inches): $1.00 ea. Size: Medium: 18 mm tall x 62 mm wide (0.7 x 2.4 inches): $2.00 ea. Size: Large: 22 mm tall x 76 mm wide (1.3 x 3 inches): $3.00 ea. Installation
instructions for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions
|
|||||
Custom
Die
Cut Decal for Brake Calipers. Extremely high quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. COLORS: Black, Silver, White, Red. Size: Small: 14 mm tall x 42 mm wide (0.55 x 1.65 inches): $1.00 ea. Size: Medium: 18 mm tall x 54 mm wide (0.7 x 2.1 inches): $2.00 ea. Size: Large: 22 mm tall x 66 mm wide (1.3 x 2.6 inches): $3.00 ea. Installation
instructions for die cut decals: https://www.prancingmoose.com/VolvoBodyStickers.html#decalinstructions
|
PARTS LABELS |
WINDOW / GLASS LABELS |
Brrrrrrrrrr Air Conditioned
Sticker TYPE 1 CLEAR Background (clear film with blue text). This is an Inside Window Label (with adhesive on the front). Approx. 4 inches x 1.3 inch (146 x 55 mm): $5.00 ea. |
||
LAMBDA SOND
re-creation inside window decal. The original Lambda Sond decal shown at left appeared on 240/260 models beginning in 1976 (for 1977 models) when Vovo introduced the Oxygen Sensor Feedback Loop to their Bosch K-Jetronic fuel injection system. It was originally applied as a reverse inside window decal in the 240/260 lower rear window. LAMBDA SOND Reverse Inside Window Decal Size: 110 mm wide x 80 mm tall (4.3 x 3.1 inches): $5.00 ea. When done shopping, please proceed to SHIPPING: |
||
VOLVO, A car you can believe in (special white print, clear background decal). Available with adhesive ON REAR or ON FRONT (inside glass decal). SIZE: 97 mm (3.8 inches): $6.00 Re-creation of original vintage decal. |
||
VOLVO CARS TORSLANDA GOTHENBURG. DIE CUT DECAL (White, no background). High quality outdoor UV resistant vinyl. Adhesive on REAR. Die cut and mounted on professional transfer material. SIZE: 10 inches (254 mm) : $10.00 |
||
RADIO CODE inside glass window label 1154763. Reverse Inside Window Label. SILVER BACKGROUND. Adhesive on FRONT. This decal originally appeared on Volvo glass (mounted on the inside), facing out. Part number: 1154763. Size: about 3.5 x 2 inches: $7.00 |
||
VOLVO ALARM (style #1) inside glass window label. Special Reverse Inside Window Label printed on CLEAR FILM. Adhesive on FRONT. This decal originally appeared on Volvo glass (mounted on the inside), facing out. Size: about 3 inches wide (75 mm): $7.00 |
||
VOLVO GUARD ALARM (style #2) inside glass window label. Special Reverse Inside Window Label printed on CLEAR FILM. Adhesive on FRONT. This decal originally appeared on Volvo glass (mounted on the inside), facing out. Size: about 3.25 inches wide (82 mm): $7.00 |
||
Example: 1995 850 T5R
|
VOLVO ALARM (style #3) inside glass window label. Special Reverse Inside Window Label. Adhesive on FRONT. This decal appeared on Volvo glass (mounted on the inside), facing out. Size: about 2.9 x 1.2 inches (73 x 31 mm): $5.00 |
|
On Call Window Label (style #1). Reverse Inside Window Label. Adhesive on FRONT. Black with silver-gray text. Size: 2 3/4 inches wide: $5.00 |
||
On Guard On Call Window Label (style #2). Reverse Inside Window Label. Adhesive on FRONT. Red and black with silver-gray text. Size: 2 3/4 inches wide: $6.00 |
||
Drive Safely sticker. Available as a regular vinyl sticker or as a Reverse Inside Window Label. Size: 3 inches x 7/16 inch (76 x 11 mm): 4.00 ea. Size: 5 inches x 3/4 inch (127 x 19 mm): 6.00 ea. |
||
OVNINGSKOR
sticker. Used on the rear of cars in Sweden when a new driver is "practicing" driving. Available as a regular printed vinyl sticker or optional with magnetic backing. Size: 16 x 3 inches (660 x 76 mm): $16.00 ea. Size: 10 x 1.8 inches (254 x 45 mm): $8.00 ea. When done shopping, please proceed to SHIPPING: |
||
Window Label Caution - AWD, Flatbed Tow Only. Available as self-adhesive Vinyl Sticker or Reverse Cling Window Decal. SIZE: 5 x 1.7 inches. PRICE: $5.00 When done shopping, please proceed to SHIPPING: |
||
Anti-Theft Sticker (style #1)
"This Vehicle
Protected by Anti-Theft Sticker." Regular vinyl sticker or as a Reverse Inside Window Label with Adhesive on FRONT. Size: 2.5 x 1 inch: $4.00 |
||
Anti-Theft
Sticker (style #2) "Vehicle
Fitted
with Anti-Theft System." Regular vinyl sticker or as a Reverse Inside Window Label with Adhesive on FRONT. Size: 2.5 x 1 inch: $4.00 |
||
Assembled in CANADA -
Halifax Nova Scotia, CLEAR Window Decal for inside of back glass. This custom CLEAR label may be placed on the inside of the rear window. The Halifax plant was in operation from 1963 to 1998. This custom re-creation has a special CLEAR BACKGROUND made with adhesive on FRONT for mounting on the INSIDE of the glass. Size approx. 10.5 x 1.25 inches (267 x 32 mm). $9.00 each When done shopping, please proceed to SHIPPING: |
||
Halifax 30 Year Commemorative Sticker. This is a custom re-creation of the rare 30 year commemorative sticker released in 1993. It was originally made as a reverse inside window decal. Available as a printed vinyl sticker or as a reverse inside window decal. Size: 4 inches x 2.3 inches (102 x 58 mm): $6.00 each When done shopping, please proceed to SHIPPING: |
||
VOLVO LEVELLING SYSTEM This is a recreation of the VOLVO LEVELLING SYSTEM decal that was offered with the 240 rear shock system. This decal was made as an INSIDE GLASS DECAL and usually found placed on a rear window. Size: about 76 x 63 mm. $6.00 When done shopping, please proceed to SHIPPING: Round sticker "DO NOT TURN" found on air pump. $3.00 When done shopping, please proceed to SHIPPING: |
||
WARNING - Parts May
Fall Off at Any Time - VOLVO Size: 3 x 1.7 inches (76 x 43 mm): 4.00 each Size: 4 x 2.2 inches (102 x 56 mm): 5.00 each Size: 5 x 2.7 inches (127 x 69 mm): 6.00 each |
||
WARNING - Parts May
Fall Off at Any Time (no brand) This version may still be ordered HERE: Partsmayfalloff |
||
WARNING - VOVO RULES Label for
Visor, Dash or Glass (or place it anywhere). Available as a printed vinyl sticker with matte finish (magnetic backing may be added) or as an inside window reverse decal. TWO SIZES. Size: 4 x 2.25 inches (102 mm x 57 mm): $4.00 each Size: 5 x 2 inches (127 mm x 51 mm): $5.00 each When done shopping, please proceed to SHIPPING: Note about sticking to plastic surfaces: If
you will be placing this sticker on a plastic dash or
sun visor, care must be taken to thoroughly CLEAN the
surface. Regardless
of the surface type, any grease, oil or vinyl dressing residue (such
as Armour All) will defeat the adhesive and cause the
sticker to un-stick. So I recommend a good
cleaning and then wiping the surface with alcohol,
acetone or similar anti-grease solvent before putting
on the sticker.
The best treatment is
using an Adhesion Promoter, such as 3M 4298 Adhesion
Promoter, Sponge Applicator (Amazon link). I now offer
this item HERE.
|
||
TEST
VEHICLE or OFFICIAL TEST VEHICLE Die Cut Decal DIE CUT DECAL (White vinyl, no background) adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. MULTIPLE SIZES TEST VEHICLE Size: approx. 6 x 1 inches (152 mm x 26 mm): Price: $4.00 each Size: approx. 8 x 1.4 inches (203 mm x 35 mm): Price: $5.00 each Size: approx. 10 x 1.75 inches (254 mm x 44 mm): Price: $6.00 each MULTIPLE SIZES OFFICIAL TEST VEHICLE Size: approx. 8 x 0.850 inches (203 mm x 21 mm): Price: $5.00 each Size: approx. 10 x 1.1 inches (254 mm x 27 mm): Price: $6.00 each Size: approx. 12 x 1.3 inches (254 mm x 33 mm): Price: $8.00 each When done shopping, please proceed to SHIPPING: |
||
NO ONE SUSPECTS THE VOVO Die Cut Decal DIE CUT DECAL (White, no background) adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. Size: approx. 10 x 0.65 inches (254 mm x 16 mm): Price: $7.00 each Size: approx. 20 x 1.3 inches (508 mm x 32 mm): Price: $14.00 each COLOR: WHITE. When done shopping, please proceed to SHIPPING: Installation instructions
for decals: prancingmoose.com/decalinstructions
|
||
NO ONE SUSPECTS THE VOVO - 240 PROFILE Die Cut Decal DIE CUT DECAL (White, or other), no background, adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. SIZE: 8 inches long: $7.00 SIZE: 10 inches long: $9.00 COLOR: WHITE When done shopping, please proceed to SHIPPING: |
||
NO ONE SUSPECTS THE VOVO - WAGON PROFILE Die Cut Decal DIE CUT DECAL (White, or other), no background, adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. SIZE: 8 inches long: $7.00 SIZE: 10 inches long: $9.00 COLOR: WHITE When done shopping, please proceed to SHIPPING: |
||
NO ONE SUSPECTS THE VOVO - FWD PROFILE Die Cut Decal DIE CUT DECAL (White, or other), no background, adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. SIZE: 8 inches long: $7.00 SIZE: 10 inches long: $9.00 COLOR: WHITE When done shopping, please proceed to SHIPPING: Installation instructions
for decals: prancingmoose.com/decalinstructions
|
||
NO ONE SUSPECTS THE VOVO - XC40 PROFILE Die Cut Decal DIE CUT DECAL (White, or other), no background, adhesive on back. High quality outdoor UV resistant vinyl. Die cut and mounted on professional transfer material. SIZE: 8 inches long: $7.00 SIZE: 10 inches long: $9.00 COLOR: WHITE When done shopping, please proceed to SHIPPING: Installation instructions
for decals: prancingmoose.com/decalinstructions
|
||
SRS SIPS Glass Decal Special inside glass decal with clear background. The photo to the left is an original decal on an 850 windshield. This is made to replicate that decal. Size: about 45 x 30 mm: $5.00 |
INTERIOR / CABIN LABELS |
Early Model Caution Dash Label
- Spicer Thornton
Power-Lok This very rare label was found on the dash of a 1964 544 that had been assembled in Halifax. This is a reproduction printed on vinyl (self-adhesive back) and gloss laminated. Size: approx. 2 x 1.4 inches (51 mm x 35 mm) Price: $5.00 When done shopping, please proceed to SHIPPING: |
|||||||||||
240 R-Sport (Rallye) Gauge Cluster "OKTAN" label. 98 Octane or 93 Octane. Size: approx. 25 mm (1 inch). $4.00 When done shopping, please proceed to SHIPPING: |
|||||||||||
ORIGINAL FADED TEXT
|
240 Gauge Cluster Label (1981-93) UNLEADED GASOLINE ONLY or PREMIUM GASOLINE ONLY If the white lettering on your 240 instrument cluster is fading, like the photo at the left, here is a new label shown below to renew it. This new label has a matte non-glare finish. Cleaning of the plastic surface is strongly recommended before installing an overlay. PRICE: $4.00 ea. When done shopping, please proceed to SHIPPING: Note about sticking to plastic surfaces: This sticker goes on a plastic instrument panel. Care must be taken to thoroughly CLEAN the surface. Regardless of the surface type, any dirt, grease, oil or vinyl dressing residue (such as Armour All) or even finger prints will defeat the adhesive and cause the sticker to un-stick. I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||||||||||
240 Wiper Lever Restoration Labels FULL SET OF LABELS FOR ALL 240 WIPER LEVER STYLES If your 240 wiper lever text and images are fading away, you may now renew it with a new overlay. This is a group set of multiple different graphic image vinyl labels from several different styles of 240 wiper levers. It will match a variety of years. The large label is for a 245 wagon with rear glass wiper. It was carefully designed to wrap around three sides of the lever. Or if needed it can be cut apart and pieces can be installed. These have a matte non-glare finish. Thorough cleaning of the lever is required before installing an overlay. PRICE: $5.00 per set When done shopping, please proceed to SHIPPING: Note about sticking to plastic surfaces: This sticker goes on the plastic wiper lever. Care must be taken to thoroughly CLEAN the surface. Regardless of the surface type, any dirt, grease, oil or vinyl dressing residue (such as Armour All) or even finger prints will defeat the adhesive and cause the sticker to un-stick. A wiper lever is usually really grimy, so I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||||||||||
240 Wiper Lever Label CUSTOM This label is for a 245 wagon lever used for a rear glass wiper. A customer asked for this custom label, which he planned to use on a sedan with custom wiring to operate the headlamp wash/wipe independently. This label is designed to wrap around three sides of the lever like the above label and has a matte non-glare finish. Thorough cleaning of the lever is required before installing an overlay. PRICE: $5.00 When done shopping, please proceed to SHIPPING: Note about sticking to plastic surfaces: This sticker goes on the plastic wiper lever. Care must be taken to thoroughly CLEAN the surface. Regardless of the surface type, any dirt, grease, oil or vinyl dressing residue (such as Armour All) or even finger prints will defeat the adhesive and cause the sticker to un-stick. A wiper lever is usually really grimy, so I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||||||||||
240 Turn Signal and Cruise Control Lever Restoration Overlay Here is the new overlay installed below. If your 240 turn signal / cruise control lever text and images are fading away, you may now renew it with a new overlay. This adhesive backed label was carefully designed to wrap around three sides of the lever. It has a matte non-glare finish. Thorough cleaning of the lever is require before installing an overlay. PRICE: $5.00 When done shopping, please proceed to SHIPPING: If you have the more plain lever shown here, then the above label can be trimmed to fit only a portion of the label for this lever. Note about sticking to plastic surfaces: This sticker goes on the plastic wiper lever. Care must be taken to thoroughly CLEAN the surface. Regardless of the surface type, any dirt, grease, oil or vinyl dressing residue (such as Armour All) or even finger prints will defeat the adhesive and cause the sticker to un-stick. A wiper lever is usually really grimy, so I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||||||||||
OLD FACEPLATE
|
Early 240 Light Switch
Overlay Dash Label, Black If your old 240 "LIGHTS" faceplate is faded like this one on the left, now you may add a new black overlay to renew it. This plate may be easily removed after pulling off the knob. The new overlay will fit precisely on the plate and then you may re-install it. There is no worry of decreasing night view because this plate it is not equipped with any back-lighting. When done shopping, please proceed to SHIPPING: |
||||||||||
1986-93 240 Light Knob
Overlay Label, Black Choose Style 1 (offset) or Style 2 (centered). If your 240 light knob image is faded or missing you may add a new black overlay to renew it. The offset image has been found on 1986-87 240s. The centered image seems to be on all 1988-93 240s. Thorough cleaning of the knob surface is required before adhering an overlay. Matte finish. PRICE: $4.00 . When done shopping, please proceed to SHIPPING: |
|||||||||||
Fading Images
TEXT STYLESYMBOL STYLE |
240 Vent Button Labels (Set of
3 labels) TWO STYLES: TEXT Style: 1981 to 1984 or SYMBOL Style: late-1984 to 1993 If the text or symbols on your old 240 vent buttons are ugly or getting hard to read, here are some inexpensive labels to renew them. These labels are printed on durable adhesive backed vinyl with a matte black finish. The SYMBOL STYLE began in some 1984 models and was in use for all models from 1985 to 1993. TWO STYLES: TEXT or SYMBOLS PRICE: $4.00 for the set of 3. When done shopping, please proceed to SHIPPING: Note about sticking to plastic surfaces: These stickers go on plastic dash buttons. Care must be taken to thoroughly CLEAN the surface. Any dirt, grease, oil or vinyl dressing residue (such as Armour All) or even finger prints will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||||||||||
240
Classic Dash Panel Overlay Volvo produced a limited series of numbered "Classic" 240 versions. These were the final 1,600 cars produced for North America and Volvo placed a printed label on the dash panel with the car's number. If you have a rare 1993 Volvo 240 Classic and your original dash label is faded or missing, here's a new custom label that will accurately replicate the original. It can be placed on your old dash plate or on a blank dash plate. Custom printed overlay. Your custom number may be added. When done shopping, please proceed to SHIPPING: |
|||||||||||
240
Classic Limited Edition Dash Panel Overlay, Matte finish I discovered that Volvo produced a DIFFERENT limited series of "Classic" 1993 240 versions (sedan and wagons) for some non-U.S. markets. This Classic edition found in Japan was generally sold with higher options. The dash panel shown below has been found on 1993 244 and 245 Classics in Japan. I have replicated the original overlay and it can be placed on your blank 240 dash plate as shown. When done shopping, please proceed to SHIPPING: |
|||||||||||
240
TACK Limited Edition Dash Panel Overlay Volvo also produced a limited series of 1993 240 versions known as 240 TACK for the Japanese market. This was a final limited run of 500 1993 240s (sedans and wagons) to commemorate the end of the 240 line. These cars were normally lessor optioned cars. "TACK" is translated from Swedish to English as "THANKS." I have replicated the original overlay here and it can be placed on your blank 240 dash plate as shown. When done shopping, please proceed to SHIPPING: |
|||||||||||
'Turbo' or 'INTER COOLER Turbo' 240 Dash Panel Overlay. Custom matte finish overlay label for the 240 dash. You can upgrade your 240 Turbo interior in a classic way and put this on a blank dash plate. Matte finish black overlay with light gray text.
When done shopping, please proceed to SHIPPING: |
|||||||||||
240 Dash Panel Overlay. Custom matte finish overlay for the 240 dash. You can upgrade your 240 interior in a classic way and put this on a blank dash plate.. Matte finish black overlay with light gray text. Older style '240' text or newer style '240' text. . When done shopping, please proceed to SHIPPING: |
|||||||||||
240 PRANCING MOOSE Dash Panel Overlay. Custom matte finish overlay for the 240 dash. You can upgrade your 240 interior in a classic MOOSE way and put this on a blank dash plate.. Matte finish black overlay with light gray moose. . When done shopping, please proceed to SHIPPING: |
|||||||||||
GRAY Antenna Switch Window for Rare GRAY Switches. When done shopping, please proceed to SHIPPING:
|
|||||||||||
COLOR OPTIONS:
Black, Rebel Blue, Red or Carbon Fiber.
ORDER HERE: Start Button Overlay Sticker: $3.00 each.
When done shopping, please proceed to SHIPPING:
Note about sticking to plastic surfaces: This sticker goes on the plastic start button. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) or even oily finger prints will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE.
Also it may be helpful to warm this label as you
place it on the curved shape button to help the
vinyl conform easier to the shape. A hair drier or
heat gun can be used.
|
|||||||||||
SHIFT PATTERN LABEL For manual transmission models. <<< This label originally came on manual trans models, such as the V70R image at left. Matte finish. Size: about 1 inch (25 mm). Available with BLACK background or GRAY background. When done shopping, please proceed to SHIPPING: |
|||||||||||
|
|||||||||||
Label located on Right Seat Slider, 850. PN 3521600. Matte finish. $4.00 |
140, 164, 240 Fuse Door Cover Labels |
1973 140, 164 Fuse Panel Cover
Label 1212715. Short fuse cover length approx. 20 cm / 7.75 inches. 12 fuses. Sticker found on inside of fuse cover door. PN 1212715 for 12 fuse panel. Printed vinyl (adhesive back) matte finish. Size: approx 1.3 x 7 inches (33 mm x 180 mm): $8.00 |
||
Early 240 to 1978 240 Fuse Panel Cover
Label 1215506, White. Short fuse cover (approx. 22 cm / 8.5 inches). 12 fuses. Sticker found on inside of fuse cover door. This one is PN 1215506. Early 240 up to 1978. Printed vinyl (adhesive back) matte laminated. Label size: approx 1.25 x 7.3 inches (32 mm x 185 mm): $8.00 |
||
Early 240 to 1978 240 Fuse Panel Cover
Label 1247670, White/Orange. Short cover (approx. 22 cm / 8.5 inches). 12 fuses. Sticker found on inside of fuse cover door. This one is PN 1247670. Early 240 up to 1978. Printed vinyl (adhesive back) matte laminated. Label size: approx 1.25 x 7.3 inches (32 mm x 185 mm): $8.00 |
||
Early 240 up to 1978 Fuse Panel Cover
Label 1255037, Light Red. Short fuse cover (approx. 22 cm / 8.5 inches). 12 Fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1255037, UNKNOWN YEAR early 240 to 1978. Printed vinyl (adhesive back) matte laminated. Label size: approx 1.25 x 7.3 inches (32 mm x 185 mm): $8.00 |
||
1979 240 Fuse Panel Cover
Label 1225698, Yellow. For medium short fuse cover (29 cm / 11.4 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1225698 found on a 1979 242. Printed vinyl (adhesive back) matte laminated. Size: approx 1.3 x 9 inches (33 mm x 229 mm): $8.00 |
||
1979 240 Fuse Panel Cover
Label 1304547, Green. For medium short fuse cover (29 cm / 11.4 inches).16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1304547 found on a 1979 242. Printed vinyl (adhesive back) matte laminated. Size: approx 1.3 x 9 inches (33 mm x 229 mm): $8.00 |
||
1982 240 Fuse Panel Cover Label 1244921, fluorescent red. For medium short fuse cover (29 cm / 11.4 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1244921, found on a 1982 240 Turbo. Printed vinyl (adhesive back) matte laminated. Size: approx 1.3 x 9 inches (33 mm x 229 mm): $8.00 |
||
1983 240 Fuse Panel Cover Label 1313555,
Yellow. For medium short fuse cover (29 cm / 11.4 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1313555, 1983 240. Printed vinyl (adhesive back) matte laminated. Size: approx 1.3 x 9 inches (33 mm x 229 mm): $8.00 |
||
1984 240 Fuse Panel Cover
Label 1350094. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1350094 found on a 1984 240 Turbo. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm): $8.00 |
||
240
Fuse Panel Cover Label For long fuse cover (32 cm / 12.5 inches). 16 fuses. SPECIAL CUSTOM This custom label was created to simplify things, so a lot of useless text was removed (including eliminating French text). This custom label was given PN 1350094-2 with CUSTOM text created for a 240 Turbo.
Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm). |
||
1985 240, 240 Turbo Fuse Panel Cover Label 1360159. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1360159 for 1985 240 and 240 Turbo. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm): $8.00 |
||
240 Fuse Panel Cover
Label1350390. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1350390, (year uncertain) 240 in North America. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 8 3/4 inches (73 mm x 222 mm): $8.00 |
||
1986 240 Fuse Panel Cover
Label 1360304. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1360304, 1986 240 in North America. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 8 3/4 inches (73 mm x 222 mm): $8.00 |
||
240 Fuse Panel Cover
Label 1364394. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 1364394 (year uncertain). Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 8 3/4 inches (73 mm x 222 mm): $8.00 |
||
1987-88 240 Fuse Panel Cover Label 3501079. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 3501079, 1987-88 240 in North America. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 8 3/4 inches (73 mm x 222 mm): $8.00 |
||
1990-91 240 Fuse Panel Cover
Label 3528472. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 3528472, 1990-91 240 (possibly other years). Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm): $8.00 |
||
1992 240 Fuse Panel Cover Label 3536434. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 3536434, 1992 (and possibly 1993) 240 with Power/Heated Rear View Mirrors. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm): $8.00 |
||
1993 240 Fuse Panel Cover
Label 9430081. For long fuse cover (32 cm / 12.5 inches). 16 fuses. Sticker found on inside of fuse cover at lower left kick panel. This one is PN 9430081, 1993 240. Printed vinyl (adhesive back) matte laminated. Size: approx 2 7/8 x 9 inches (73 mm x 228 mm): $8.00 |
Glove Box Vehicle Capacity Label |
|
1981-82 240 Vehicle Capacity 1320491 - Tire Pressure. Glove Box Door. May be found on passenger door or on GLOVE BOX DOOR for this year. Version found on PASSENGER DOOR door is found >HERE<. PN 1320491, 1981-82 240. Photo at left is glove box from a 1982 245. Vinyl (with adhesive back), gloss laminated. Size: approx 4 x 2.6 inches (102 x 68 mm): $5.00 |
Rear Facing Seat and Seat Belt Warning Labels |
Rear Facing Seat Large Label
(Japanese), gloss finish. Large label that explains the correct positioning of the rear facing child seat and seat belts in a wagon. 1995 960 Estate but may also be found on other 700/900/90 series Estates. The label is found on the underside of the cargo area floor panel that lifts up to expose the seat. Size: 11.7 x 8.2 inches (297 x 209 mm): $16.00 |
|
Rear Facing Seat Large Label (large), gloss finish 9488617. Large label that explains the correct positioning of the rear facing seat belts in a 940 Estate. PN 9488617. Size: 11.25 x 4.4 inches (286 x 111 mm): $14.00 |
|
Rear Facing Seat Label (small), gloss finish 9488618. Smaller label that explains the correct positioning of the rear facing seat belts in a 940 Estate. PN 9488618. Size: 2.6 x 2.6 inches (67 x 67 mm): $5.00 |
|
Rear Facing Seat Label (small), gloss finish 9488619. Smaller label that explains the correct positioning of the rear facing seat belts in a 940 Estate. PN 9488619. Size: 2.6 x 2.6 inches (67 x 67 mm): $5.00 |
|
UNDERHOOD, ENGINE, DRIVELINE . |
U N D E R H O O D , E N G I N E , D R I V E L I N E L A B E L S | ||
AC Labels | Alarm SIREN Label | Assembled in HALIFAX |
Battery Labels | Brakes ABS | Brake Booster or MC Labels |
Castrol Synthetic Oil Label | COOLANT Labels | Diesel Labels |
Drive
Belts WARNING |
E1 E2 E4 E5 Labels | Electrical Labels Under Hood |
Emission Labels | Fuse Labels Under Hood | HID Headlights Warning |
Ignition COIL Labels | Ignition CONTROL UNIT Labels | Import Label (France) |
Intercooler Labels | M46 Transmission Labels | Oil Cap Warning Label |
Power Steering Labels |
||
Radiator Labels | Rear Axle Labels | SRS - Airbag |
Timing Belt Service Labels | Timing Cover Labels ORANGE | Timing Cover Labels WHITE |
Turbo CAUTION Labels ORANGE |
Vacuum Labels 240-260 | Vacuum Labels 740 |
Vacuum Labels CUSTOM | Valve Cover Label B20E | Version Label Under Hood |
VIN Labels | WARNING: Drive Belts and Fan Labels ORANGE |
Wiper Motor Label 240 |
ABS Brakes |
1996 850 T5R |
ABS Control Unit Label 9401542, 850 This label was found on the ABS control unit for a 1995 850 T5R. May apply to other years. Size about 66 x 56 mm. $5.00 |
ABS Control Unit Label 9140933, 850 This label was found on the ABS control unit for an 850. May apply to other years. Gloss finish: $4.00 |
|
ABS Control Unit Label 10.0447-0733.3, 850 This label was found on the same car and ABS control unit as above for an 850, on a different side. May apply to other years. Gloss finish: $4.00 When done shopping, please proceed to SHIPPING: |
|
ABS Control Unit Label 10.0501-7857.3, 850 This label was found on the ABS control unit brake distribution block for an 850 (same car as above labels). May apply to other years. Gloss finish: $4.00 When done shopping, please proceed to SHIPPING: |
Assembled or Imported Labels |
Assembled in HALIFAX Label This label was found on the radiator support as shown in this 240 photo. It was placed on cars made in Halifax. The Halifax plant was in operation from 1963 to 1998. Size approx. 90 mm x 30 mm (3.5 x 1.2 inches). gloss finish. PRICE: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces: You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
IMPORTATEUR VOLVO FRANCE Label This label was found on the right shock tower of a 1984 240 sold in France. It was placed next to the VIN plate. Part number 1313397. Size: 68 mm x 17 mm. Matte finish. PRICE: $3.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces: You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
1978 240 |
Bitte beachten "Please note" German Import Label ENGLISH INTERPRETATION: "Please note! For this VOLVO - only VOLVO - Use Original Parts and Accessories for reasons of Safety and Warranty. Drive safely - Drive VOLVO" This label was found under the hood on the radiator support for a 1978 Volvo imported to Germany. Size: approx. 86 mm x 68 mm. Matte finish. $8.00 |
Battery or Electrical Labels |
Early Volvo 6-volt Voltage Regulator
Label (Yellow) Printed vinyl label. Adhesive on back. Matte finish. "VDT-UBE 322/5" at bottom. SIZE: 74 x 37 mm (2.9 x 1.5 inches): $5.00 PRICE: $5.00 When done shopping, please proceed to SHIPPING: |
|
Battery 850 Model
|
Battery Label 9128862 PN 9128862, Printed vinyl (adhesive back) gloss laminated. This label was found on an original battery in a 1995 850 T5R. Approx 74 x 56 mm (2.9 x 2.2 inches): $5.00 |
Battery Label 9459946 Allows you to add a label to a non-Vovo battery. PN 9459946, Printed vinyl (adhesive back) gloss laminated. 4 x 2.2 inches (102 mm x 56 mm): $5.00 |
|
Battery Label 30745774 Allows you to add a label to a non-Vovo battery. PN 30745774, Printed vinyl (adhesive back) gloss laminated. SIZE: 4 x 2.2 inches (102 mm x 56 mm): Price: $5.00 |
|
Battery Label 30772221 600A Allows you to restore a Vovo battery or add a label to a non-Vovo battery. This label has been seen on models from the 1990s to present. PN 30772221, Printed vinyl (adhesive back) gloss laminated. SIZE: 4.25 x 2.25 inches (108 mm x 57 mm): Price: $5.00 |
|
Battery Label 30772231 800A Allows you to restore a Vovo battery or add a label to a non-Vovo battery. This label has been seen on models from the 1990s to present. PN 30772231, Printed vinyl (adhesive back) gloss laminated. SIZE: 4.25 x 2.25 inches (108 mm x 57 mm): Price: $5.00 |
|
Battery Label 30772219, 220, 221, 222, 223 (600A) Allows you to add a label to a non-Vovo battery. Typically found on a Group 94R battery, which is about 12 inches long. This label has been seen on models from the 1990s to present. PN 30772219, Printed vinyl (adhesive back) gloss laminated. SIZE: 4.5 x 1.4 inches (114 x 36 mm): Price: $5.00 |
|
Battery Label 30772229, 230, 231, 232, 233 (800A) Allows you to add a label to a non-Vovo battery. Typically found on a Group 49 battery, which is about 14 to 15 inches long. This label has been seen on models from the 1990s to present. PN 30772229, Printed vinyl (adhesive back) gloss laminated. SIZE: 6.5 x 2.4 inches (165 x 63 mm): Price: $7.00 |
|
Large Battery Side Label There was a time years ago when you could actually buy a nice looking Vovo battery that actually had a label like this on it. Printed vinyl (adhesive back), matte finish. SIZE: 8 x 2.2 inches (203 x 56 mm): $6.00 SIZE: 10 x 2.75 inches (254 x 70 mm): $8.00 (size pictured in top left photo). A typical Group 34 battery for 240 is 10 inches wide. A larger Group 48 battery is about 12 inches wide. |
|
|
1993 240 Battery Lower Fuse Block COLOR LABEL. . This is a label found on the SIDE of the late 1993 240 fuse block. The colors represent the colors of the fuses used. If you see this fuse block next to your battery in your 240, this label can be seen on the side. Durable printed vinyl with clear matte finish. PRICE: $5.00 When done shopping, please proceed to SHIPPING: |
1993 240 Battery FUSE BLOCK Top Cover Overlay. This is a black printed vinyl OVERLAY to restore the text and boxes on the top of this fuse cover. Found in a late 1993 240 next to the battery. Durable printed vinyl with clear matte finish. PRICE: $5.00 When done shopping, please proceed to SHIPPING: |
|
1995 850 Model
|
850 Loom Harness Cover Label The original label is made from silver foil. This reproduction is gray vinyl, matte finish, adhesive back. This label was found in a 1995 850 T5R. PN 6849841. SIZE: Approx. 60 x 60 mm: $5.00 When done shopping, please proceed to SHIPPING: |
|
1995 850 Fuse Door Label This label was found in a 1995 850 T5R. PN 9128755. SIZE: Approx. 177 x 53 mm, matte finish: $9.00 |
35 Amp Cooling Fan Fuse Label 9454284 PN 9454284. Found on radiator support of circa 2000 FWD-AWD cars. Printed vinyl (adhesive back), matte finish. SIZE: Approx. 130 x 25 mm: $5.00 |
|
MORE BATTERY LABELS CAN BE ADDED. IF YOU FIND ONE THAT IS NOT HERE, PLEASE EMAIL. |
240 Wiper Motor Label |
140, 164, and 1975-82 240
Wiper Motor Label, Yellow "nahentstört" Printed vinyl label. Adhesive on back. Gloss finish. Normally found on 140 (1974) wiper motor and 164 (1973-75), plus found on 1975-82 240/260. These are the motors that have a rounded end as seen in these photos. This decal will wrap around the motor barrel. It may be easiest to place on the motor before it is installed in the car or if the motor is loosened away from the firewall. PRICE: $6.00 When done shopping, please proceed to SHIPPING: |
Ignition Labels |
KNOWN 240 IGNITION CONTROL UNITS NUMBERS (CHRYSLER TYPE 1981-1988) If you can add to this list please email. 1317873 Found on 1982 240. 1317295 Found on 1981, 1982, 1983, 1984 (compatible with 8111226). 1346105 Found on 1984. 1346107 Found on 1985, 1986, 1987 (compatible with 1985-88). 1357308 Found on 1988 (compatible with 1985-88). 3517641 Found on 1986, 1988 (compatible with 1985-88). |
|
Ignition Control Unit (ICU) top label, 1317873 (BLUE). Printed vinyl (adhesive back), gloss laminated. Size: 92 mm x 32 mm (3.6 x 1.25 inches): $5.00 each Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC ICU SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
Ignition Control Unit (ICU) top label, 1346107 (BLUE). Found on ignition box for 240 from 1985 and later. LIGHT Blue or DARK Blue. This label will appear as light blue or sometimes a dark blue label. Printed vinyl (adhesive back), gloss laminated. Size: 92 mm x 32 mm (3.6 x 1.25 inches): Price: $5.00 each |
|
Ignition Coil Labels |
1970 142 |
Ignition
Super Coil Label Set (red/yellow). Coil Labels (Set of 2) found on some early Volvos. Printed vinyl (adhesive back), Matte laminated. Size: 60 mm x 30 mm (2.4 x 1.2 inches) and 38 x 38 mm (1.5 x 1.5 inches) Price: $4.00 for the set of 2 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1976 240
|
Ignition Coil
Label Electronic Ignition "Made in Germany" (yellow). Coil Label found on 1976 to (unknown) Volvo 240 with ELECTRONIC IGNITION. Printed vinyl (adhesive back), Matte laminated. Size: 50 mm x 25 mm (2 x 1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: CLICK HERE Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1979 240
|
Ignition Coil
Label "IND. BRASILEIRA" (RED). Coil Label found on some early 240s (approx. 1979-81) and other models. Printed vinyl (adhesive back), Matte laminated. Size: 52 mm x 25 mm (2 x 1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Ignition Coil
Label "Made in Spain" (RED). Coil Label found on some early 240 and other models. Printed vinyl (adhesive back), Matte laminated. Size: 55 mm x 27 mm (2.2 x 1.1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
Ignition Coil
Label "Made in Brazil" (blue). Coil Label found on some 740/940 models. Printed vinyl (adhesive back), Matte laminated. Size: 55 mm x 27 mm (2.2 x 1.1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1991 240
1992 940 Turbo
|
Ignition Coil
Label "Made in Spain" (yellow). Coil Label found on many 240 models 1989 to 1993. Also some 940 models. Printed vinyl (adhesive back), Matte laminated. Size: 50 mm x 25 mm (2 x 1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1980 240
|
Ignition Coil
Label TCI "made in Germany" (electric bolt on left side). Coil Label found on some early 240 models through approximately 1981. Volvo PN for this coil is believed to be: 35254 (later 1219189). Printed vinyl (adhesive back), Matte laminated. Size: 52 mm x 25 mm (2 x 1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Ignition Coil
Label "made in Germany" (GREEN) Coil Label found on 1986 to 1988 240 models (possibly earlier years). Coil is identified as Volvo PN 1336137, Bosch PN 0 221 122 345. Printed vinyl (adhesive back), Matte laminated. Size: 52 mm x 25 mm (2 x 1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1987 740
|
Ignition Coil
Label "Made in Brazil" (gray). Coil Label found on 1987-1993 740, 760, 780, 940 models. The Bosch PN on the bottom may be 0 221 118 351. Printed vinyl (adhesive back), Matte laminated. Size: 55 mm x 27 mm (2.2 x 1.1 inches) Price: $2.00 each When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Square Ignition Coil (IGNITOR) Small
Label "Made in Slovenia" (yellow).
When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the PLASTIC COIL SURFACE. You MUST take extra care to thoroughly CLEAN the heck out of any surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
MORE IGNITION LABELS CAN BE ADDED. IF YOU FIND ONE THAT IS NOT HERE, PLEASE EMAIL. |
Valve Cover, Cam Cover, Oil Cap Labels |
B20E Emission Control label for 1800 / 142 Valve Cover. Two color blue versions have been seen on original engines. Top left photo is from a 1971 1800E. Bottom left photo is a 1971 142S. Printed vinyl (adhesive back), matte finish. Size: 82 mm x 45 mm (3.2 x 1.8 inches): $6.00 each Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on a hot valve cover. You MUST take extra care to thoroughly CLEAN the surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. |
|||
B20E CHECK BELT TENSION ACC. label for 1800 / 140 Valve Cover. Two version colors of blue have been seen on original engines. Top left photo is from a 1971 1800E. Bottom left photo is a 1971 142S. Printed vinyl (adhesive back), matte finish. Size: 75 mm x 35 mm (3 x 1.4 inches): $6.00 each Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on a hot valve cover. You MUST take extra care to thoroughly CLEAN the surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. |
|||
B30A Emission Control label for 164 Valve Cover. Printed vinyl (adhesive back), matte finish. Size: 82 mm x 45 mm (3.2 x 1.8 inches): $6.00 each Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on a hot valve cover. You MUST take extra care to thoroughly CLEAN the surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. |
|||
B30A CHECK BELT TENSION ACC. label for 164 Valve Cover. Same Label as above B20 label. Printed vinyl (adhesive back), matte finish. Size: 75 mm x 35 mm (3 x 1.4 inches): $6.00 each Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on a hot valve cover. You MUST take extra care to thoroughly CLEAN the surface you put it on. Regardless of the surface type, any grease, oil or vinyl dressing residue will defeat the adhesive and cause the sticker to un-stick, usually once it gets hot. |
|||
Oil
Cap Warning Label. 240,
740 engines, 1313455. PN 1313455. Reproduction of the original yellow warning label found on a B21/B23 metal oil cap and on a B230 cam cover. Special printed sticker for high temperatures (adhesive back), matte laminated. Size: 62 mm x 32 mm wide (2.4 x 1.25 inches): $5.00
|
|||
Synthetic Engine Oil
Sticker Vovo Castrol, 31416043, Black. Typically found under the hood on the radiator support of some models. PN 31416043. Printed vinyl sticker (adhesive back), gloss laminated. SIZE: 2.5 x 0.75 inches (65 x 20 mm): $3.00 |
|||
Castrol Edge Professional Oil Sticker, 31416623, Black. PN 31416623. Printed vinyl sticker (adhesive back), gloss laminated. SIZE: 2.5 x 0.75 inches (65 x 20 mm): $3.00 Typically found under your hood on the radiator support. |
|||
ATTENTION! Synthetic Engine Oil
Sticker Vovo Castrol - Black No part number. Printed vinyl sticker (adhesive back), gloss laminated. SIZE: 4 x 1.5 inches (102 x 38 mm): $5.00 Typically found under your hood on the radiator support. |
|||
Timing Belt Service Labels |
This
is a collection of service labels I created by request a number of
years ago. These labels offer the usual timing belt interval
service, as well as other commonly replaced engine
accessories.
If you think a new service label should be made available, please ask. Size: approx 80 mm tall x 65 mm wide (3.1 x 2.5 inches) Many are still available Some are hated by you-know-who and are crossed out. You can see which ones. Note about sticking to plastic surfaces: This sticker may go on the radiator support or timing cover. Care must be taken to thoroughly CLEAN the any surface you are sticking to, especially if it's plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and maybe then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter (primer), such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE.
|
Timing Cover Labels |
T I M I N G C O V E R L A B E L S | |
Orange Timing Cover Labels | Timing Cover 1985-87 |
Timing Cover 1988-93 | Timing Cover 1994-95 |
WHITE BLOCK Labels | |
Camshaft Belt Label 940/960 |
240 Red Block ORANGE Timing Cover Number
Labels. Adhesive on back. Special ultra-aggressive adhesive. These labels appeared on 240 engines from 1976 until 1984 (and some early 1985 cars). They always had a 3-digit number, like the 960 label shown at left. This 3-digit number is the last three numbers of the engine part number and these labels were placed on all engines by the manufacturer before being installed into the car. PARTIAL LIST OF NUMBERS BELOW NUMBERS ARE DESIGNATED FOR USA CARS UNLESS NOTED. 1976 B21A 314 (Europe) 1976 B21F 304, 305, 312 (USA) 1976 B21 (unknown) 630 1977 B21A 528 (Europe) 1977 B21F 516, 519 1978 B21F 578, 580, 581 1979 B21A 772 (Europe) 1979 B21E 776 (Europe) 1979 B21F 778, 779, 780, 781, 782, 783, 788, 789 1979 B23E 786 (Europe, Australia) 1980 B21A 810, 811, 812, 918 (Europe) 1980 B21E 824, 825, 826, 827, 828 (Europe) 1980 B23E 834 (Europe) 1980 B21F 830, 831, 832, 833, 848, 849 1981 B21E 916, 917, 924, 925 (Europe) 1981 B21ET 886 (Europe) 1981 B21F 892, 893, 894, 895, 896, 897, 920, 921 1981 B21FT 898 1981 B23A 968, 870 (Europe) 1981 B23E 900, 901, 902, 903, 904, 922, 923 (Europe) 1982 B19ET 986 (Sold in Italy) 1982 B21E 954, 955 (Europe) 1982 B21F 960, 961, 962, 963, 964, 965 1982 B21ET 910, 958 (Sold in Sweden, Europe) 1982 B21FT 966, 967, 993 1982 B23A 940, 980, 991 (Europe) 1982 B23E 972, 973, 974, 975, 978, 979 (Europe) 1983 B19ET 986 (Sold in Italy) 1983 B21A 944, 947 (Europe) 1983 B21E 954, 955 (Europe) 1983 B21ET 860, 958 (Sold in Sweden, Europe) 1983 B21F 965 1983 B21FT 800, 801 1983 B23E 812, 813, 974, 975 (Europe) 1983 B23F 802, 803, 890 1984 B19ET 878 (Sold in Italy) 1984 B21ET 872, 884 (Europe) 1984 B21F 905 1984 B21FT 868, 869, 926, 927 1984 B23E 844, 845, 888, 889 (Europe) 1984 B23F 846, 847, 944, 945 Some early 1985 B21FT engine received this label. 1985 B21FT 868, 868, 926, 927 (Most late 1985 B21FT engines received the larger WHITE 1985 label below) ANY special Custom Number is also available if requested: 240 242 244 245 Adhesive on back. Special ultra-aggressive adhesive. SIZE: approx 1 7/8 inches x 15/16 inch (48 x 24 mm): Price: $6.00 ea. O R D E R H E R E :
Adhesive on back. Special ultra-aggressive adhesive. Note about sticking to engine or plastic surfaces: In most cases this sticker goes on a plastic timing cover. Care must be taken to thoroughly CLEAN the surface. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning, then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The absolute best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item if needed HERE. |
||
Late-1985 240 Turbo Timing Cover Label B21FT, ET. Late 1985 B21FT, ET. This one came from a 1985 240 Turbo. Some EARLY 1985 240 Turbo engines got the ORANGE sticker above. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 inches (82 mm x 52 mm): $5.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1985-87 240 Timing Cover Label B230F. 1985-87 240 with B230F. This one came from a 1985 240 and this style label was used from 1985 to 1987. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 inches (82 mm x 52 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1985-87 740 Timing Cover Label B230A, B230F, or B230K. 1985-87 740 with B230. This one is for a 1985 to 1987 740 non-turbo with B230A, F or K engine. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 inches (82 mm x 52 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1985-87 740 Turbo Timing Cover Label
B230ET or FT. 1985-87 740 with B230FT or ET. This one is for a 1985 to 1987 740 Turbo engine. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 inches (82 mm x 52 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1988 240
1993 240
|
1988-93 240 or 740 (non-turbo) Timing Cover
Label B230F, FD. 1988-93 240, 740 or 940 with B230F. This one came from a 1990 240. It appears to have been in use from 1988 to 1992. Some labels had a 'K' or 'L' as shown in some of these photos. The 'K' was used from 1988 to mid-1993 (designating a K-block). The 'L' was used from mid-1993 to 1995 (designating an L-block. Many stickers from the early 1988 model year and the late 1993 model year did not have an 'L' or 'K'. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 1/8 inches (82 mm x 54 mm). CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
1989 740 Turbo B230ET
|
1988-93 700-900 Turbo Timing Cover
Label B200, B230, ET or FT. 1988-93 740/760/780/940 with B230FT or ET. These appear to have begun use on 1988 to 93 models. Some labels had a 'K' or 'L' as shown in some of these photos. The 'K' was used from 1988 to mid-1993 (designating a K-block). The 'L' was used from mid-1993 to 1995 (designating an L-block. Not all stickers had this letter. Many from early 1988 and late 1993 production did not have an 'L' or 'K'. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2 1/8 inches (82 mm x 54 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
1995 940 B230FD
|
1994-95 940 Timing Cover Label
(with bar code) This label appears to have come on a 1994-95 940 with B230 FD or B230 FK engine. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2.25 inches (82 mm x 57 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
1996 WHITE BLOCK Engine Timing Cover Label. This one was found on a 1996 960 with B6304 6 cylinder engine. Printed vinyl, self-adhesive back, gloss laminated. Size: 2.5 x 1.75 inches (65 mm x 45 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Mid-2000s WHITE Block Engine Timing Cover Label. This one came from a mid-2000s S60 with B5244 T5 engine. Printed vinyl, self-adhesive back, gloss laminated. Size: approx. 3.25 x 2.25 inches (82 mm x 57 mm): $7.00 CUSTOM PRINTING AVAILABLE. Price: $7.00 each
Note about sticking to plastic surfaces: This sticker goes on the plastic timing cover. Care must be taken to thoroughly CLEAN the surface if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning and wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Timing Cover Camshaft Belt Label 9430183. PN 9430183. Found on a some late 940 (4 cylinder) and 960 (6 cylinder) front timing cover. Printed vinyl, self-adhesive back, gloss laminated. Size: 68 mm x 27 mm (about 2.7 x 1 inches): $5.00 |
||
POWER STEERING LABELS |
|
Power Steering Label - Early 240 SEEKING PHOTOS AND DIMENSIONS This metal power steering reservoir was found on early 240 models (1975-76). If you can help to provide good images and dimensions of this label so it can be reproduced, please email. CONTACT |
|
WARNING: HID HEADLIGHTS
| |
2004 V70R
|
WARNING: High Voltage HID Headlights YELLOW PN 30651013. Found under the hood of 2001-2005 and some 2006 FWD/AWD cars equipped with HID headlights, including S60R/V70R. TWO are found on each car behind headlights. Printed vinyl, self-adhesive back, gloss laminated. $4.00 each |
2006 S60R
2007 S60R
|
WARNING: High Voltage HID Headlights YELLOW-BLACK PN 30760152. Found under the hood of some 2006 and all 2007 (and later) FWD/AWD cars equipped with HID headlights, including S60R/V70R. TWO are found on each car behind headlights or on headlight rear cover. Printed vinyl, self-adhesive back, gloss laminated. $4.00 each |
WARNING: FAN and DRIVE BELT LABELS
|
||
|
||
1976-81 240
Rotating
Fan Warning Label - Fluorescent Orange 1247681. Adhesive on back. Special ultra-aggressive adhesive. PN 1247681, 240. Printed label, matte laminated. Mounted on radiator fan shroud for most 1976-77 240s. Mounted on radiator support for most 1978-81 240s and 260s. Size: approx. 7.8 x 1.4 inches (195 mm x 35 mm). Price: $8.00 each When done shopping, please proceed to SHIPPING: Adhesive on back. Special ultra-aggressive adhesive. Note about sticking to hot underhood surfaces (especially plastic): This sticker usually goes on the metal radiator support or on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1982 240 Diesel
1990 240 |
1982-90 240 Rotating
Fan Warning Label - Fluorescent Orange 1313187.
Adhesive on back. Special ultra-aggressive adhesive. PN 1313187, 240. Printed label, matte laminated. Mounted on radiator support for 240 DL, GL and Turbo 1982-90. Size: approx. 7 1/4 inches x 1 5/8 inches (183 mm x 40 mm): $8.00 Adhesive on back. Special ultra-aggressive adhesive. Note about sticking to hot underhood surfaces (especially plastic): This sticker usually goes on the metal radiator support or on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
NEW REPRODUCTION |
1981-85 240 Turbo Caution
Label - Fluorescent
Orange 1338651.
Adhesive on back. Special ultra-aggressive adhesive. Normally found on top of cooling fan shroud for 240 Turbo. Appeared on BOTH non-intercooled fan shroud and intercooled fan shroud.. PN 1338651, 240 Turbo. Printed label, matte laminated. Size: approx. 8 1/2" x 3/4" (220 mm x 18 mm): $8.00 Adhesive on back. Special ultra-aggressive adhesive. Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
1986 740 Turbo
|
240 and 740 Turbo Intercooler Label - RED, 1349815.
This sticker was normally found on top of the intercooler. PN 1349815, 240 Turbo with intercooler and early 740/760 Turbo (excluding 780 Turbo). Matte finish decal. Size: approx. 9 1/2" x 3/4" (240 mm x 18 mm): $6.00 |
|
Warning Self-Starting Fan
Label W124 NO PART NUMBER. Found on 940 or other models. Vinyl (with adhesive back), gloss laminated. Size: 5.25 x 0.8 inches (133 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Warning Self Starting Fan
Label W215 NO PART NUMBER. Found on 940 or other models (this one was on a 1992 940 Turbo). Vinyl (with adhesive back), gloss laminated. Size: 5.25 x 0.8 inches (133 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
1994 940
|
Warning Self Starting Fan
Label W338 NO PART NUMBER. Found on a 1994 940. Vinyl (with adhesive back), gloss laminated. Size: 5.25 x 0.8 inches (133 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
Warning Self Starting Fan
Label W515 NO PART NUMBER. Found on a 1995 940. Vinyl (with adhesive back), gloss laminated. Size: 5.25 x 0.8 inches (133 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): This sticker usually goes on the plastic fan shroud. Care should be taken to thoroughly CLEAN the heck out of any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||
Warning Self Starting Fan
Label, "Assembled in Canada." NO PART NUMBER. Found on 940/960 or other models. Vinyl (with adhesive back), gloss laminated. Size: 4.7 x 0.8 inches (120 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: |
||
Warning Self Starting Fan
Label - 850 NO PART NUMBER. Found on some 850 or other models. Vinyl (with adhesive back), gloss laminated. Size: 4.7 x 0.8 inches (120 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: |
||
1994-95 850
|
Warning Attention Drive Belts 850 9340072 PN 9430072, found on 1994-95 850, possibly others. Vinyl (with adhesive back), gloss laminated. Size: 4.25 x 0.6 inches (108 mm x 15 mm): $5.00 |
|
1995 850 T5R
|
Warning Self Starting Fan
Label W439 - 850 NO PART NUMBER. Just number W439. This label was found on a 1995 850 T5Rs. Vinyl (with adhesive back), gloss laminated. Size: 135 mm x 19 mm: $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: |
|
2004 S60R
|
S60 V70 Warning Attention Rotating
Drive Belt Label 9454160. PN 9454160, found on many FWD/AWD models. Vinyl (with adhesive back), gloss laminated. Size: 2.75 x 1.5 inches (70 mm x 38 mm): $5.00 |
|
S40 Warning Attention Rotating
Drive Belt Label 30865946 - Golden Yellow PN 30865946, found on 2001 and later S40 engine. Vinyl (with adhesive back), gloss laminated. Size: 3.75 x 0.7 inches (95 mm x 18 mm): $6.00 |
||
2005 S60R
|
Warning Self-Starting Fan
Label, 30896588. PN 30896588, found on radiator support of many FWD/AWD models, beginning in 2001 on the S40 and on this 2005 S60R in the photo at left. Vinyl (with adhesive back), gloss laminated. Size: 5 x 0.8 inches (127 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: |
|
2004 S60R
|
Warning Self-Starting Fan
Label, 9430301. PN 9430301, found on radiator support of many FWD/AWD models, starting with the 850 and on 2004-2006 S60R, V70R. Vinyl (with adhesive back), gloss laminated. Size: 5 x 0.8 inches (127 mm x 20 mm): $4.00 Price: $4.00 When done shopping, please proceed to SHIPPING: Note about sticking to underhood surfaces (especially plastic): Care should be taken to thoroughly CLEAN any surface you put it on, especially if sticking to plastic. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All) will defeat the adhesive and cause the sticker to un-stick, unually once it gets hot. So I recommend a good cleaning and then wiping the surface with rubbing alcohol, acetone or similar solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|
2002 S40
|
Warning Self-Starting Fan
Label, 30859782. PN 30859782, found on radiator support of a 2002 S40 and other late model FWD/AWD models. Vinyl (with adhesive back), gloss laminated. Size: 4.7 x 0.8 inches (120 mm x 20 mm): $5.00 |
|
Warning Fan and Drive Belt
Label - Black PN 31333045, found on radiator support of late model FWD/AWD models. Vinyl (with adhesive back), gloss laminated. Size: approx. 2.5 x 0.8 inches (65 mm x 20 mm): $5.00 |
||
MORE DRIVE BELT WARNING LABELS CAN BE MADE. IF YOU FIND ONE THAT IS NOT HERE, PLEASE EMAIL. |
|
|||
For Door, Pillar or Inner Body SRS Labels CLICK HERE | |||
1992 240
|
ATTENTION! SRS
VEHICLE! Small Yellow Label. PN 3536210, found under hood on left inner fender (see photo). Found on a 1990-93 240 with SRS Airbag and SRS equipped 700/900 models. Vinyl (with adhesive back), gloss laminated. Size: 1.44 x 1 inches (36 x 25 mm): $3.00 For Door, Pillar or Inner Body SRS Labels CLICK HERE |
||
1995 850T5R 2000 V70
2004 C70
|
ATTENTION! SRS VEHICLE 3536448 PN 3536448, found under hood on hood bottom surface for 850, 60 and 70 series. Vinyl (with adhesive back), gloss laminated. Size about 3.7 x 2 inches (93 x 50 mm): $5.00 |
||
Warning Label Japanese - Yellow PN 9430341, 940. Size: 62 x 33 mm (2.4 x 1.3 inches): $2.00 |
|||
Warning Label Japanese - Yellow-White PN 31283321, 940. Size: 87 x 31 mm (3.4 x 1.2 inches): $4.00 |
Brakes |
||||
1800ES
|
1800 Ate Bremsgerat T51 Brake Servo Label (Blue) For 1800ES. SIZE: approx. 64 x 22 mm. Matte finish. PRICE: $4.00 each When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a brake servo. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1800ES
|
1800 3.6127-0201.4 Brake Servo Label TYPE 1 (Blue, no border) For 1800ES. SIZE: approx. 48 x 10 mm. Matte finish. PRICE: $4.00 each When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a brake servo. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1800ES |
1800 3.6127-0201.4 Brake Servo Label TYPE 2 (Blue, with border) For 1800ES. SIZE: approx. 48 x 10 mm. Matte finish. PRICE: $4.00 each When done shopping, please proceed to SHIPPING: |
|||
|
Bendix Brake Booster Label 1229336 (for 240) STYLE #1 TEXT STYLE #2 TEXT This style label has been found on the brake vacuum servo for 240 models. It has been verified so far on a 1983 240 and a 1993 240 (with different manufacture dates of course). This label has Volvo PN 1229336 (240 brake booster part number). The original label was a fragile paper label with an oversized square of clear film. Original labels rarely survived long. This new label is durable vinyl with a similar oversized square of clear film for authenticity. Label Size: Overall 65 x 40 mm. Gloss finish. Custom text changes are possible. PRICE: $5.00 When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a brake servo. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1995 940
|
Bendix Brake Booster Label 9157699 (for 940) STYLE #1 TEXT
Label Size: Overall 65 x 40 mm. Gloss finish. Custom text changes are possible. PRICE: $5.00 When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a brake servo. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
1992 940
|
Bendix Brake Booster Label 3516094 (for 940) STYLE #2 TEXT 940 This label was found on a brake vacuum servo for a 1992 940. It's for Volvo PN 3516094 (brake booster part number). The original label was a fragile paper label with an oversized square of clear film. Original labels rarely survived long. This new label is durable vinyl with a similar oversized square of film for authenticity. Label Size: Overall 65 x 40 mm. Gloss finish. Custom text changes are possible. PRICE: $5.00 When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a brake servo. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
Brake Booster 1995 850 T5R |
Ate Brake Booster Label 9140236 (for 1995 850 T5R) This label was found on a brake vacuum servo for 1995 850 T5R. It's for Volvo PN 9140236 (brake booster part number). This new label is durable vinyl, gloss finish. Label Size: approx. 47 x 20 mm. $4.00 |
|||
Brake Booster 1995 850
|
Ate Brake Booster Label 9140237 (for 850) This label was found on a brake vacuum servo for 1992-97 850 model. It's for Volvo PN 9140237 (brake booster part number). This new label is durable vinyl, gloss finish. Label Size: approx. 47 x 20 mm. $4.00 |
|||
Master Cylinder 1995 850
|
Ate Master Cylinder Label 9140448 (for 850) This label was found on a brake master cylinder for the 850 model. It's for Volvo PN 9140448. This new label is durable vinyl, gloss finish. Label Size: approx. 44 x 18 mm. $4.00 |
|||
Master Cylinder 1995 850
|
Ate Brake Reservoir Label for 850. This small label was found on the top of a brake fluid reservoir for the 850 model. Gloss finish. Label Size: approx. 20 mm. $3.00 When done shopping, please proceed to SHIPPING: |
|||
Under Hood Version Labels |
||||
1980 240
|
Under Hood Version Label 1246468 An equipment version label is found in the trunk of a 240 sedan made after 1981, however this label appears under the hood on the 1980-81 models (photo). PN 1246468. White vinyl (with adhesive back), gloss laminated Size: approx 5.5 x 2.25 inches (140 mm x 58 mm): $6.00 |
|||
|
||||
1967 1800S
1967 123 GT
1961 PV544 Sport
|
B18 Radiator Label (yellow) SIZE: approx 75 x 25 mm. This labels appeared on radiators for B18 cars beginning in 1961. The precise year range is uncertain. Car in top left photo is a 1967 1800S. Car in middle photo is a 1967 123 GT. Car in lower photo is a 1961 PV544 Sport with B18. PRICE: $4.00 each When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a hot metal radiator cap. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
|||
Round Coolant Radiator Cap Label (RED/Black) These labels appeared on early Volvo (120 / 1800 / 140) radiators. SIZE: approx 43 mm. PRICE: $5.00 each When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a hot metal radiator cap. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||||
Round Coolant Reservoir Cap Label (WHITE/Red) These labels appeared on Volvo (1800, 140) coolant reservoirs. SIZE: approx 53 mm. PRICE: $5.00 each When done shopping, please proceed to SHIPPING: Note about sticking to HOT surfaces: This sticker usually goes on a hot metal reservoir cap. Care must be taken to thoroughly CLEAN the surface before sticking a label. Regardless of the surface type, any grease, oil or vinyl dressing residue (such as Armour All, etc.) will defeat the adhesive and cause the sticker to un-stick. So I recommend a good cleaning then wiping the surface with alcohol, acetone or similar anti-grease solvent before putting down the sticker. The best treatment is using an Adhesion Promoter, such as 3M 4298 Adhesion Promoter, Sponge Applicator (Amazon link). I now offer this item HERE. |
||||
Early Red/White Rectangle Coolant Labels I have received sources worldwide on the below early coolant label versions that have been used in Volvos. These are all of the Red/White rectangular coolant labels found so far with no part numbers. Careful attention to detail has been made in re-creating them to appear as close to original as possible. If you have any information that will help to improve in this endeavor, please email. |
||||
Style 1: 1800E
and 120/Amazon Coolant Label RED/WHITE (white border). Style 1: White with Red text. White outer border. This one appeared on some 120/Amazon and 1800 models. Top left photo: Inner fender. Bottom left photo: Coolant reservoir. No part number. Vinyl (with adhesive back), matte finish. Size: approx: 4.5 x 2 inches (114 x 51 mm): $6.00 |
||||
SAME AS ABOVE Style 1: 1800E and 120/Amazon Coolant Label RED/WHITE (white border). <<< Also found on 240 or 260 reservoir 1976-1979. RED/WHITE (white border) Style 1: White with Red text. White outer border. No part number. Vinyl (with adhesive back), matte finish. Size: approx: 4.5 x 2 inches (114 x 51 mm): $6.00 |
||||
Style 1: 1800E, 120/Amazon, 240 Coolant Label. RED/WHITE (white border). Special FADED RED Style 1: White with FADED Red text. White outer border. This one appeared on some 120/Amazon, 1800 and early 240 models. No part number. Vinyl (with adhesive back), matte finish. Size: approx: 4.5 x 2 inches (114 x 51 mm): $6.00 |
||||
Style 2: 120 / 1800 / 140 / 164
Coolant Label. RED/WHITE (red outer border). Style 2: White with Red text. Red outer border. This one appeared mostly on 140 models (TOP photo at left). It's similar to the white/red 120/1800 label above, but clearly NOT the same. It has also been found on the 1800S, 1800E (2nd photo LEFT 1970 model) and on 164 models (see 3rd photo LEFT 1971 model). It was generally used from 1964 through 1974 models. No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4 x 1.8 inches (102 x 46 mm): $6.00 |
||||
Style 2: 120 / 1800 / 140 / 164
Coolant Label. RED/WHITE (red outer border). Special FADED RED. Style 2: White with Red text. Red outer border. This one appeared mostly on 140 models (TOP photo at left). It's similar to the white/red 120/1800 label above, but clearly NOT the same. It has also been found on the 1800S, 1800E (2nd photo LEFT 1970 model) and on 164 models (see 3rd photo LEFT 1971 model). It was generally used from 1964 through 1974 models. No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4 x 1.8 inches (102 x 46 mm): $6.00 |
||||
1969 144
|
Style 3: 120 / 123 GT / Amazon / 140
Coolant Label. RED (white border). Style 3: Red with White text. White outer border. This one appeared on some 120 / Amazon and 140. Top PHOTO at left: original example found on a 123GT. Second PHOTO at left was found on a 1969 144 radiator support. No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4.5 x 2 inches (114 x 50 mm): $6.00 |
|||
Style 3: 120 / 123 GT / Amazon / 140
Coolant Label. RED (white border). Special FADED RED. Type 3: Red with White text. White outer border. This one appeared on some 120 / Amazon and 140. Top PHOTO at left: original example found on a 123GT. No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4.5 x 2 inches (114 x 50 mm): $6.00 |
||||
Style 4: 1800S
Coolant Label. RED (white border). Style 4:Type 4: Red with White text. White outer border. This one appeared on some 1800 models (PHOTO: found on 1800S). No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4.5 x 2 inches (114 x 50 mm): $6.00 |
||||
Style 4: 1800S
Coolant Label. RED (white border). Special FADED RED. Style 4: Red with White text. White outer border. This one appeared on some 1800 models (PHOTO: found on 1800S). No part number. Vinyl (with adhesive back), GLOSS finish. Size: approx: 4.5 x 2 inches (114 x 50 mm): $6.00 |
||||
Style 5: Mystery
Coolant Label found on 1980 262 Bertone. RED (no border). No part number. English on top, French below. If you can help with more info about this mystery label, please email. |
||||
Coolant Reservoir 1980 and later. |
||||
1982 244 GL (UK)
1982 244 GL (UK)
|
Coolant Reservoir Label 1297524 Found on 240 coolant reservoir. Pictured car is a 1982 244 GL from the UK. PN 1297424. Vinyl (with adhesive back), gloss finish. Size: approx 3.75 x 1.25 inches (95 mm x 32 mm): $5.00 |